相关头文件: misc.h
1.1 NVIC_PriorityGroupConfig函数 /*** @brief Configures the priority grouping: pre-emption priority and subpriority.* @param NVIC_PriorityGroup: specifies the priority grouping bits length. * This parameter can be one of the following values:* @arg NVIC_PriorityGroup_0: 0 bits for pre-emption priority* 4 bits for subpriority* @arg NVIC_PriorityGroup_1: 1 bits for pre-emption priority* 3 bits for subpriority* @arg NVIC_PriorityGroup_2: 2 bits for pre-emption priority* 2 bits for subpriority* @arg NVIC_PriorityGroup_3: 3 bits for pre-emption priority* 1 bits for subpriority* @arg NVIC_PriorityGroup_4: 4 bits for pre-emption priority* 0 bits for subpriority* @retval None*/void NVIC_PriorityGroupConfig(uint32_t NVIC_PriorityGroup);功能:设置优先级分组：先占优先级和从优先级参数:NVIC_PriorityGroup：优先级分组位长度 返回值:无 1.2 NVIC_PriorityGroup类型 /** @defgroup Preemption_Priority_Group * @{*/#define NVIC_PriorityGroup_0 ((uint32_t)0x700) /*!< 0 bits for pre-emption priority4 bits for subpriority */#define NVIC_PriorityGroup_1 ((uint32_t)0x600) /*!< 1 bits for pre-emption priority3 bits for subpriority */#define NVIC_PriorityGroup_2 ((uint32_t)0x500) /*!< 2 bits for pre-emption priority2 bits for subpriority */#define NVIC_PriorityGroup_3 ((uint32_t)0x400) /*!< 3 bits for pre-emption priority1 bits for subpriority */#define NVIC_PriorityGroup_4 ((uint32_t)0x300) /*!< 4 bits for pre-emption priority0 bits for subpriority */ 1.3 NVIC_Init函数 /*** @brief Initializes the NVIC peripheral according to the specified* parameters in the NVIC_InitStruct.* @param NVIC_InitStruct: pointer to a NVIC_InitTypeDef structure that contains* the configuration information for the specified NVIC peripheral.* @retval None*/void NVIC_Init(NVIC_InitTypeDef* NVIC_InitStruct)功能:根据 NVIC_InitStruct 中指定的参数初始化外设 NVIC 寄存器参数:NVIC_InitStruct：指向结构 NVIC_InitTypeDef 的指针，包含了外设 GPIO 的配置信息 返回值:无 1.4 NVIC_InitTypeDef类型 typedef struct{uint8_t NVIC_IRQChannel; //指定要启用或禁用的IRQ通道uint8_t NVIC_IRQChannelPreemptionPriority;//指定的IRQ通道的抢占优先级uint8_t NVIC_IRQChannelSubPriority; //指定的IRQ通道的次级优先级FunctionalState NVIC_IRQChannelCmd; //IRQ通道是启用还是禁用 } NVIC_InitTypeDef;NVIC_IRQChannel取值
#ifdef STM32F10X_MDADC1_2_IRQn = 18, /*!< ADC1 and ADC2 global Interrupt */USB_HP_CAN1_TX_IRQn = 19, /*!< USB Device High Priority or CAN1 TX Interrupts */USB_LP_CAN1_RX0_IRQn = 20, /*!< USB Device Low Priority or CAN1 RX0 Interrupts */CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */TIM1_BRK_IRQn = 24, /*!< TIM1 Break Interrupt */TIM1_UP_IRQn = 25, /*!< TIM1 Update Interrupt */TIM1_TRG_COM_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt */TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */TIM2_IRQn = 28, /*!< TIM2 global Interrupt */TIM3_IRQn = 29, /*!< TIM3 global Interrupt */TIM4_IRQn = 30, /*!< TIM4 global Interrupt */I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */SPI1_IRQn = 35, /*!< SPI1 global Interrupt */SPI2_IRQn = 36, /*!< SPI2 global Interrupt */USART1_IRQn = 37, /*!< USART1 global Interrupt */USART2_IRQn = 38, /*!< USART2 global Interrupt */USART3_IRQn = 39, /*!< USART3 global Interrupt */EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */RTCAlarm_IRQn = 41, /*!< RTC Alarm through EXTI Line Interrupt */USBWakeUp_IRQn = 42 /*!< USB Device WakeUp from suspend through EXTI Line Interrupt */ #endif /* STM32F10X_MD */成员NVIC_IRQChannelPreemptionPriority可赋的值：最大取值15，具体有上面设置的优先级组中规定的位数决定 成员NVIC_IRQChannelSubPriority可赋的值：最大取值15，具体有上面设置的优先级组中规定的位数决定 成员NVIC_IRQChannelCmd可赋的值：ENABLE or DISABLE
02. 外部中断相关API 2.1 GPIO_EXTILineConfig void GPIO_EXTILineConfig(uint8_t GPIO_PortSource, uint8_t GPIO_PinSource);功能:选择 GPIO 管脚用作外部中断线路参数:GPIO_PortSource: 选择用作外部中断线源的 GPIO 端口GPIO_PinSource：待设置的外部中断线路 返回值:无参数：GPIO_PortSource 选择用于EXTI线的GPIO端口
/** @defgroup GPIO_Port_Sources * @{*/#define GPIO_PortSourceGPIOA ((uint8_t)0x00)#define GPIO_PortSourceGPIOB ((uint8_t)0x01)#define GPIO_PortSourceGPIOC ((uint8_t)0x02)#define GPIO_PortSourceGPIOD ((uint8_t)0x03)#define GPIO_PortSourceGPIOE ((uint8_t)0x04)#define GPIO_PortSourceGPIOF ((uint8_t)0x05)#define GPIO_PortSourceGPIOG ((uint8_t)0x06)参数：GPIO_PortSource 选择用于EXTI线的GPIO端口
/** @defgroup GPIO_Pin_sources * @{*/#define GPIO_PinSource0 ((uint8_t)0x00)#define GPIO_PinSource1 ((uint8_t)0x01)#define GPIO_PinSource2 ((uint8_t)0x02)#define GPIO_PinSource3 ((uint8_t)0x03)#define GPIO_PinSource4 ((uint8_t)0x04)#define GPIO_PinSource5 ((uint8_t)0x05)#define GPIO_PinSource6 ((uint8_t)0x06)#define GPIO_PinSource7 ((uint8_t)0x07)#define GPIO_PinSource8 ((uint8_t)0x08)#define GPIO_PinSource9 ((uint8_t)0x09)#define GPIO_PinSource10 ((uint8_t)0x0A)#define GPIO_PinSource11 ((uint8_t)0x0B)#define GPIO_PinSource12 ((uint8_t)0x0C)#define GPIO_PinSource13 ((uint8_t)0x0D)#define GPIO_PinSource14 ((uint8_t)0x0E)#define GPIO_PinSource15 ((uint8_t)0x0F) 2.2 EXTI_Init void EXTI_Init(EXTI_InitTypeDef* EXTI_InitStruct);功能:根据 EXTI_InitStruct 中指定的参数初始化外设 EXTI 寄存器参数:EXTI_InitStruct：指向结构 EXTI_InitTypeDef 的指针，包含了外设 EXTI 的配置信息 返回值:无EXTI_InitTypeDef类型
typedef struct{uint32_t EXTI_Line; //中断线EXTIMode_TypeDef EXTI_Mode; //中断模式EXTITrigger_TypeDef EXTI_Trigger; //中断触发方式FunctionalState EXTI_LineCmd; //中断功能使能}EXTI_InitTypeDef;EXTI_Line
/** @defgroup EXTI_Lines * @{*/#define EXTI_Line0 ((uint32_t)0x00001) /*!< External interrupt line 0 */#define EXTI_Line1 ((uint32_t)0x00002) /*!< External interrupt line 1 */#define EXTI_Line2 ((uint32_t)0x00004) /*!< External interrupt line 2 */#define EXTI_Line3 ((uint32_t)0x00008) /*!< External interrupt line 3 */#define EXTI_Line4 ((uint32_t)0x00010) /*!< External interrupt line 4 */#define EXTI_Line5 ((uint32_t)0x00020) /*!< External interrupt line 5 */#define EXTI_Line6 ((uint32_t)0x00040) /*!< External interrupt line 6 */#define EXTI_Line7 ((uint32_t)0x00080) /*!< External interrupt line 7 */#define EXTI_Line8 ((uint32_t)0x00100) /*!< External interrupt line 8 */#define EXTI_Line9 ((uint32_t)0x00200) /*!< External interrupt line 9 */#define EXTI_Line10 ((uint32_t)0x00400) /*!< External interrupt line 10 */#define EXTI_Line11 ((uint32_t)0x00800) /*!< External interrupt line 11 */#define EXTI_Line12 ((uint32_t)0x01000) /*!< External interrupt line 12 */#define EXTI_Line13 ((uint32_t)0x02000) /*!< External interrupt line 13 */#define EXTI_Line14 ((uint32_t)0x04000) /*!< External interrupt line 14 */#define EXTI_Line15 ((uint32_t)0x08000) /*!< External interrupt line 15 */#define EXTI_Line16 ((uint32_t)0x10000) /*!< External interrupt line 16 Connected to the PVD Output */#define EXTI_Line17 ((uint32_t)0x20000) /*!< External interrupt line 17 Connected to the RTC Alarm event */#define EXTI_Line18 ((uint32_t)0x40000) /*!< External interrupt line 18 Connected to the USB Device/USB OTG FSWakeup from suspend event */ #define EXTI_Line19 ((uint32_t)0x80000) /*!< External interrupt line 19 Connected to the Ethernet Wakeup event */成员EXTI_Mode可赋的值：（中断模式）
typedef enum{EXTI_Mode_Interrupt = 0x00,//中断EXTI_Mode_Event = 0x04 //事件}EXTIMode_TypeDef;成员EXTI_Trigger可赋的值（中断）
typedef enum{EXTI_Trigger_Rising = 0x08, //上升沿触发EXTI_Trigger_Falling = 0x0C, //下降沿触发EXTI_Trigger_Rising_Falling = 0x10 //双边延触发}EXTITrigger_TypeDef;成员EXTI_LineCmd可赋的值： ENABLE or DISABLE
2.3 EXTI_GetITStatus /*** @brief Checks whether the specified EXTI line is asserted or not.* @param EXTI_Line: specifies the EXTI line to check.* This parameter can be:* @arg EXTI_Linex: External interrupt line x where x(0..19)* @retval The new state of EXTI_Line (SET or RESET).*/ITStatus EXTI_GetITStatus(uint32_t EXTI_Line)功能:检查指定的 EXTI 线路触发请求发生与否参数:EXTI_Line：待检查 EXTI 线路的挂起位 返回值:EXTI_Line 的新状态（SET 或者 RESET） 2.4 EXTI_ClearITPendingBit /*** @brief Clears the EXTI's line pending bits.* @param EXTI_Line: specifies the EXTI lines to clear.* This parameter can be any combination of EXTI_Linex where x can be (0..19).* @retval None*/void EXTI_ClearITPendingBit(uint32_t EXTI_Line)功能:清除 EXTI 线路挂起位参数:EXTI_Line：待清除 EXTI 线路的挂起位 返回值:无 2.5 中断回调函数 EXPORT EXTI0_IRQHandlerEXPORT EXTI1_IRQHandlerEXPORT EXTI2_IRQHandlerEXPORT EXTI3_IRQHandlerEXPORT EXTI4_IRQHandlerEXPORT EXTI9_5_IRQHandlerEXPORT EXTI15_10_IRQHandler常用的中断服务函数格式为：
void EXTI3_IRQHandler(void){if(EXTI_GetITStatus(EXTI_Line3)!=RESET)//判断某个线上的中断是否发生{//中断逻辑…EXTI_ClearITPendingBit(EXTI_Line3); //清除 LINE 上的中断标志位} } 03. 对射式红外传感器计次接线图 04. 对射式红外传感器计次程序示例CountSensor.h
#ifndef __COUNT_SENSOR_H__#define __COUNT_SENSOR_H__#include "stm32f10x.h" void count_sensor_init(void);uint16_t CountSensor_Get(void);#endif /*__COUNT_SENSOR_H__*/CountSensor.c
#include "CountSensor.h"uint16_t CountSensor_Count = 0;//初始化void count_sensor_init(void){GPIO_InitTypeDef GPIO_InitStruct;EXTI_InitTypeDef EXTI_InitStruct;NVIC_InitTypeDef NVIC_InitStruct;//使能时钟RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);//初始化GPIOGPIO_InitStruct.GPIO_Mode = GPIO_Mode_IPU ;GPIO_InitStruct.GPIO_Pin = GPIO_Pin_14;GPIO_InitStruct.GPIO_Speed = GPIO_Speed_50MHz;GPIO_Init(GPIOB, &GPIO_InitStruct);//初始化外部中断线GPIO_EXTILineConfig(GPIO_PortSourceGPIOB, GPIO_PinSource14);//初始化外部中断EXTI_InitStruct.EXTI_Line = EXTI_Line14;EXTI_InitStruct.EXTI_LineCmd = ENABLE ;EXTI_InitStruct.EXTI_Mode = EXTI_Mode_Interrupt;EXTI_InitStruct.EXTI_Trigger = EXTI_Trigger_Falling;EXTI_Init(&EXTI_InitStruct);//初始化NVICNVIC_InitStruct.NVIC_IRQChannel = EXTI15_10_IRQn;NVIC_InitStruct.NVIC_IRQChannelCmd = ENABLE ;NVIC_InitStruct.NVIC_IRQChannelPreemptionPriority = 1;NVIC_InitStruct.NVIC_IRQChannelSubPriority = 1;NVIC_Init(&NVIC_InitStruct);}uint16_t CountSensor_Get(void){return CountSensor_Count;}void EXTI15_10_IRQHandler(void){if (EXTI_GetITStatus(EXTI_Line14) == SET){/*如果出现数据乱跳的现象，可再次判断引脚电平，以避免抖动*/if (GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_14) == 0){CountSensor_Count ++;}EXTI_ClearITPendingBit(EXTI_Line14);}}main.c
#include "stm32f10x.h"#include "delay.h"#include "oled.h"#include "CountSensor.h"int main(void){ //初始化OLED_Init();OLED_ShowString(1, 1, "Count:");NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);count_sensor_init();while(1){OLED_ShowNum(1 , 7, CountSensor_Get(), 5);}return 0;} 05. 旋转编码器计次接线图【其它】
06. 旋转编码器计次程序示例encode.h
#ifndef __ENCODE_H__#define __ENCODE_H__#include "stm32f10x.h" void Encoder_Init(void);int16_t Encoder_Get(void);#endif /*__ENCODE_H__*/encode.c
#include "encode.h"int16_t Encoder_Count;void Encoder_Init(void){NVIC_InitTypeDef NVIC_InitStructure;GPIO_InitTypeDef GPIO_InitStructure;EXTI_InitTypeDef EXTI_InitStructure;RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1;GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;GPIO_Init(GPIOB, &GPIO_InitStructure);GPIO_EXTILineConfig(GPIO_PortSourceGPIOB, GPIO_PinSource0);GPIO_EXTILineConfig(GPIO_PortSourceGPIOB, GPIO_PinSource1);EXTI_InitStructure.EXTI_Line = EXTI_Line0 | EXTI_Line1;EXTI_InitStructure.EXTI_LineCmd = ENABLE;EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;EXTI_Init(&EXTI_InitStructure);NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn;NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;NVIC_Init(&NVIC_InitStructure);NVIC_InitStructure.NVIC_IRQChannel = EXTI1_IRQn;NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;NVIC_Init(&NVIC_InitStructure);}int16_t Encoder_Get(void){int16_t Temp;Temp = Encoder_Count;Encoder_Count = 0;return Temp;}void EXTI0_IRQHandler(void){if (EXTI_GetITStatus(EXTI_Line0) == SET){/*如果出现数据乱跳的现象，可再次判断引脚电平，以避免抖动*/if (GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_0) == 0){if (GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_1) == 0){Encoder_Count --;}}EXTI_ClearITPendingBit(EXTI_Line0);}}void EXTI1_IRQHandler(void){if (EXTI_GetITStatus(EXTI_Line1) == SET){/*如果出现数据乱跳的现象，可再次判断引脚电平，以避免抖动*/if (GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_1) == 0){if (GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_0) == 0){Encoder_Count ++;}}EXTI_ClearITPendingBit(EXTI_Line1);}}main.c
#include "stm32f10x.h"#include "delay.h"#include "oled.h"#include "CountSensor.h"#include "encode.h"int16_t Num;int main(void){ //初始化OLED_Init();NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);Encoder_Init();OLED_ShowString(1, 1, "Num:");while (1){Num += Encoder_Get();OLED_ShowSignedNum(1, 5, Num, 5);}return 0;} 07. 示例程序下载07-对射式红外传感器计次.rar
08-旋转编码器计次.rar
08. 附录参考: 【STM32】江科大STM32学习笔记汇总
